References
- Singh V, Manuel M. Surface modification of oilfield alloys by ultrasonic impact peening: UNS N07718, N07716, G41400, and S1740. J Mater Eng Perform 2016;25(1):338–347.
- Yao J, Wang L, Zhang Q, et al. Surface laser alloying of 17-4PH stainless steel steam turbine blades. Opt Laser Technol. 2008;40(6):838–843.
- Bressan JD, Daros DP, Sokolowski A, et al. Influence of hardness on the wear resistance of 17-4 PH stainless steel evaluated by the pin-on-disc testing. J Mater Process Technol. 2008;205(1–3):353–359.
- Ritesh P, Shanmugasundaram A. An investigation of molybdenum surface reinforcement on the hardness and wear properties of AISI 630. Trans IMF. 2018;96(2):95–102.
- Kochmański P, Nowacki J. Activated gas nitriding of 17-4 PH stainless steel. Surf Coatings Technol. 2006;200(22–23):6558–6562.
- Joshi MD, Patil RA, Ma Y-R, et al. Reciprocating wear behavior of noncoated and polymer/composite coated AISI 316L steel: role of surface mechanical attrition treatment. Tribol Trans. 2021;64(5):916–935.
- Gholipour A, Shamanian M, Ashrafizadeh F. Microstructure and wear behavior of Stellite 6 cladding on 17-4 PH stainless steel. J Alloys Compd 2011;509(14):4905–4909.
- Jojith R, Radhika N. Mechanical and tribological properties of LM13/TiO2/MoS2 hybrid metal matrix composite synthesized by stir casting. Part Sci Technol 2019;37(5):570–582.
- Shanmugasundaram A, Arul S, Sellamuthu R. Effect of flyash on the surface hardness of AA 6063 using GTA as a heat source. Metall Res Technol. 2017;114(5):8.
- Alam MT. Physical, corrosion and microstructural analysis of A356/SiC nanocomposites fabricated through stir casting process. Mater Sci Forum. 2021;1034:73–86.
- Voort V, Lampman SR, Sanders BR, et al. (2004). ASM Handbook: metallography and microstructures Volume 9.
- Ziewiec A, ZieliŃska-Lipiec AET. Microstructure of welded joints of X5CrNiCuNb16-4 (17-4 PH) martensitic stainlees steel after heat treatment. Arch Metall Mater 2014;59:965–970.
- Poorhaydari K, Patchett BM, Ivey DG. Estimation of cooling rate in the welding of plates with intermediate thickness. Weld J 2005;84(10):149–155.
- Arul S, Sellamuthu R. Application of a simplified simulation method to the determination of arc efficiency of gas tungsten arc welding (GTAW) and experimental validation. Int J Comput Mater Sci Surf Eng 2011;4(3):265–280.
- Das CR, Dey HC, Srinivasan G, et al. Weldability of 17-4PH stainless steel in overaged heat treated condition. Sci Technol Weld Join. 2006;11(5):502–508.
- Sun Y, Zhong Y, Wang L. The interaction between ϵ-copper and dislocation in a high copper 17-4PH steel. Mater Sci Eng A. 2019;756:319–327.
- Sakhawat S, Falahati A, Degischer HP, et al. Localized ageing in the heat affected zone of welded X5CrNiCuNbl6-4 and X4CrNiSiTi14-7 sheets. IOP Conf Ser Mater Sci Eng. 2014;60:012071.
- Wang J, Zou H, Li C, et al. Relationship of microstructure transformation and hardening behavior of type 17-4 PH stainless steel. J Univ Sci Technol Beijing Miner Metall Mater. 2006;13(3):235–239.
- Archard JF, Hirst W. The wear of metals under unlubricated conditions. Proc R Soc London Ser A Math Phys Sci. 1956;236(1206):397–410.
- Radhika N, Raghu R. Evaluation of dry sliding wear characteristics of LM 13 Al/B4C composites. Tribol Ind. 2015;37(1):20.
- Radhika N, Raghu R. Development of functionally graded aluminium composites using centrifugal casting and influence of reinforcements on mechanical and wear properties. Trans Nonferrous Met Soc China (English Ed). 2016;26(4):905–916.
- Jojith R, Radhika N. Reciprocal dry sliding wear of SiCp/Al–7Si-0.3 Mg functionally graded composites: influence of T6 treatment and process parameters. Ceram Int. 2021;47:30459–30470.
- Jojith R, Radhika N. Microstructure, mechanical properties and reciprocal dry sliding wear behaviour of as-cast and heat-treated TiN/Al-7Si functionally graded composite. Proc IMechE Part B: J Eng Manuf. 2022;236(10):1–15.
- Libórioa MS, Praxedesb GB, Limab LLF, et al. Surface modification of M2 steel by combination of cathodic cage plasma deposition and magnetron sputtered MoS2-TiN multilayer coatings. Surf Coat Technol. 2020;384:125327.
- Hanada K, Zhang Q, Umeda K, et al. Surface modification of tool steel by MOS2 powder shooting. J Mater Process Technol. 2004;153–154(10):170–173.