References
- AASHTO M6, 2013. Standard specification for fine aggregate for hydraulic cement concrete.
- AASHTO T176, 2017. Standard method of test for plastic fines in graded aggregates and soils by use of the sand equivalent test.
- AASHTO T27, 2014. Standard method of test for sieve analysis of fine and coarse aggregates.
- AASHTO T88, 2020. Standard method of test for particle size analysis of soils.
- AASHTO T89, 2013. Standard method of test for determining the liquid limit of soils.
- AASHTO T90, 2020. Standard method of test for determining the plastic limit and plasticity index of soils.
- AASHTO T96, 2022. Standard method of test for resistance to degradation of small-size coarse aggregate by abrasion and impact in the Los Angeles machine.
- ACI 318-08, 2008. Building code requirements for structural concrete and commentary.
- ACI 325.13R-06, 2006. Concrete pavement for rehabilitation. ACI Committee Report.
- American Concrete Pavement Association (ACPA), 1991. Guidelines for concrete overlays on existing asphalt pavements (whitetopping), Technical Bulletin TB-009P.
- Arthi, S., Narasimha, V.L., and Pandurangan, K., 2015. Finite analysis of thin whitetopped pavement. IJIRSET.
- ASTM C1583, 2013. Standard test method for tensile strength of concrete surfaces and the bond strength or tensile strength of concrete repair and overlay materials by direct tension (Pull-off Method).
- ASTM C192, 2015. Standard practice for making and curing concrete test specimens in the laboratory.
- ASTM C293, 2016. Standard test method for flexural strength of concrete (using simple beam with center-point loading).
- ASTM C39, 2021. Standard test method for compressive strength of cylindrical concrete specimens.
- ASTM C78, 2022. Standard test method for flexural strength of concrete (using simple beam with third-point loading).
- ASTM D113, 2018. Standard test method for ductility of asphalt materials.
- Astm D1754, 2010. Standard test method for effect of heat and Air on asphaltic materials (Thin-Film Oven Test).
- ASTM D2042, 2022. Standard test method for solubility of asphalt materials in trichloroethylene or toluene.
- ASTM D2170, 2010. Standard test method for kinematic viscosity of asphalts (Bitumens).
- ASTM D36, 2010. Standard test method for softening point of Bitumen (Ring-and-Ball Apparatus).
- ASTM D4791, 2017. Standard test method for flat particles, elongated particles, or flat and elongated particles in coarse aggregate.
- ASTM D5, 2017. Standard test method for penetration of bituminous materials.
- ASTM D5821, 2017. Standard test method for determining the percentage of fractured particles in coarse aggregate.
- ASTM D5976, 2021. Standard specification for type I polymer modified asphalt cement for use in pavement construction.
- ASTM D70, 2013. Standard test method for density of semi-solid bituminous materials (pycnometer method).
- ASTM D7234, 2021. Standard test method for pull-Off adhesion strength of coatings on concrete using portable pull-off adhesion testers.
- ASTM D92, 2018. Standard test method for flash and fire points by Cleveland open cup tester.
- Bahram, Munik, and Vanderbossche, Julie M., 2014. Characterization of load transfer behavior for bonded concrete overlays on asphalt, TRB annual meeting.
- Ballarini, R., and Liao, M., 2012. Mechanistic modeling of unbonded concrete overlay pavements. University of Minnesota Department of Civil Engineering.
- Bari, M.E., and Zollinger, D.G., 2016. New concepts for the assessment of concrete slab interfacial effects in pavement design and analysis. International Journal of Pavement Engineering, 17 (3), 233–244. doi:10.1080/10298436.2014.993183.
- Barman, M., et al., 2011. Development of design guide for thin and ultra-thin concrete overlays of existing asphalt pavements . Task 1. University of Pittsburgh.
- BS 1881, 2015, Testing concrete methods for analysis of hardened concrete.
- CAN/CSA A23.2-14, 2014, Obtaining and testing drilled cores for compressive strength testing.
- Chun, Sanghyun, et al., 2015. Evaluation of interlayer bonding condition on structural response characteristics of asphalt pavement using finite element analysis and full-scale field tests. Construction and Building Materials, 96, 307–318. ISSN 0950-0618, doi:10.1016/j.conbuildmat.2015.08.031.
- Fick, G., et al., 2021. Guide to concrete overlays. 4th ed. Ames, IA: National Concrete Pavement Technology Center, Iowa State University.
- Gross, J., 2023. Performance history of concrete overlays in the United States. Ames, IA: National Concrete Pavement Technology Center, Iowa State University.
- Harrington, D., et al., October 2018. Guide for concrete pavement distress assessments and solutions: identification, causes, prevention, and repair. National Concrete Pavement Technology Center, Iowa State University.
- Harrington, D., and Fick, G., 2014. Guide to concrete overlays: sustainable solutions for resurfacing and rehabilitating existing pavements. 3rd ed. Ames, IA: National Concrete Pavement Technology Center, Iowa State University.
- Hossein, Mustaque, and Sultana, Sharmin, 2010. Extending asphalt pavement life using thin white topping.
- Huang, Yang H, 2004. Pavement analysis and design. University of Kentucky, Prentice Hall.
- Khazanovich, L., et al., February 2020. Development of an improved design procedure for unbonded concrete overlays. Department of Civil and Environmental Engineering, University of Pittsburgh.
- Li, Zhichang, 2012. Redefining the failure mode for thin and ultra-thin white topping, TRB annual meeting.
- Li, Zichang, Vandenbossche, Julie M, and Dufalla, Nicole, 2013. Structural model for longitudinal cracking in bonded white topping, FHWA TPA-5-165.
- Mampearachchi, W.K, Kosgolla, J., and Tia, M., 2012. Feasibility of white topping pavements for resurfacing thin asphalt pavements.
- Mu, F., and Vandenbossche, J.M., December 2011. Development of design guide for thin and ultra-thin concrete overlays of existing asphalt pavements, task 2: review and selection of structural response and performance models. Department of Civil and Environmental Engineering, University of Pittsburgh.
- Ozer, Hasan, et al., 2012. Characterization of interface bonding between hot-mix asphalt overlay and concrete pavements: modeling and in-situ response to accelerated loading. International Journal of Pavement Engineering, 13 (2), 181–196. doi:10.1080/10298436.2011.596935.
- Park, Hae-Won, et al., 2021. Development of a design catalog for bonded concrete overlay pavements considering the regional characteristics of Korea. Sustainability, 13 (17), 9876. doi:10.3390/su13179876.
- Pereira, Deividi Da S., Balbo, José T., Khazanovich, Lev, et al., 2006. Theoretical and field evaluation of interaction between ultra-thin whitetopping and existing asphalt pavement. International Journal of Pavement Engineering, 7 (4), 251–260. doi:10.1080/10298430600798895.
- Roesler, J., 2015. Concrete pavement overlay design. 1st ed. University of Illinois Urbana-champaign.
- Roesler, R., Cervantes, V., and Amirkhanian, A., 2012. Accelerated performance testing of concrete pavement short slabs. International Journal of Pavement Engineering, 13, 494–507. doi:10.1080/10298436.2011.575134.
- Satishkumar, CH. N., and Siva Rama Krishna, U., 2019. Ultra-thin white topping concrete mix with sustainable concrete materials – a literature review. International Journal of Pavement Engineering, 20 (2), 136–142. doi:10.1080/10298436.2016.1274598.
- Sounthararajah, A., et al., August 2016. Effect of cement on the engineering properties of pavement materials. Materials Science Forum, doi: 10.4028/www.scientific.net/MSF.866.31.
- Sounthararajah, A., et al., March 2018. Early-age fatigue damage assessment of cement-treated bases under repetitive heavy traffic loading. Journal of Materials in Civil Engineering, doi: 10.1061/(ASCE)MT.1943-5533.0002250.
- Tompkins, D., Khazanovich, L., and Bolander, J.E., 2015. Lattice modeling of fracture in composite concrete pavements and overlays. International Journal of Pavement Engineering, 16 (1), 56–68. doi:10.1080/10298436.2014.893332.
- Turatsinze, A., et al., 2011. Debonding. In: B. Bissonnette, L. Courard, D. Fowler, J.L. Granju, eds. Bonded cement-based material overlays for the repair, the lining or the strengthening of slabs or pavements. RILEM State of the Art Reports, Vol. 3. Dordrecht: Springer, 107–139. doi:10.1007/978-94-007-1239-3_6
- Vandenbossche, Julie M, Duffala, N, and Li, Z, 2013. A revised thin and ultra thin bonded whitetopping design procedure, Transportation research record.
- Vandenbossche, J.M., Duffala, N., and Li, Z., 2017. Bonded concrete overlay on asphalt mechanical-empirical design procedure. International Journal of Pavement Engineering, 18 (11), 1004–1015. doi:10.1080/10298436.2016.1141410.
- Vandenbossche, J. M., and Sachs, S., 2013. Guidelines for bonded concrete overlays of asphalt: beginning with project selection and ending with construction. Technical note. University of Pittsburgh.
- Wang, Te-An, Lee, Dongkeun, and Chou, Yi-Tso, 2022. Flexural and compressive behaviours of sustainable AC/RC composite system with various supplementary materials. International Journal of Pavement Engineering, 23 (9), 2922–2936. doi:10.1080/10298436.2021.1873335.
- Zhang, H., et al., 2009. Dynamic life-cycle modeling of pavement overlay systems: capturing the impacts of users, construction, and roadway deterioration. Journal of Infrastructure Systems, 16 (4), 299–309. doi:10.1061/(ASCE)IS.1943-555X.0000017.
- Zhao, Zifeng, et al., 2020. Applications of asphalt concrete overlay on Portland cement concrete pavement. Construction and Building Materials, 264, 120045–120618. doi:10.1016/j.conbuildmat.2020.120045.